HOME | DD

Description
Creating a simple vagina.
Disclaimer. These tutorials are for educational purposes. I am not responsible for what is done with the information.

www.mediafire.com/watch/795h2b…

Begin Video Transcript.

Click on a vertice on the crotch and click "View", then "View Selected" to zoom in.

We have to choose where the slit will be.

When decided, click "Knife" on the left tool bar. Just below the 3D view area, there are options for this tool that appear. The option we are most concerned with is Ctrl: midpoint snap. This automatically cuts an edge in the middle.

Choose where the cut will begin. Bring the green square down to the first edge and press "ctrl". You will notice that the green square goes to the middle of that line. Press the left mouse button and the first part of the cut is made.

Go down, and upward like I have. Press the space bar, then the first cut is made.

Make another similar cut in the middle of the cut you just made. Then another similar cut between the outer and inner cut. Then another in the centre. I will show you.

You can zoom in with the mouse scroll wheel if you need a closer view.

Move to a view inside the model. Press "A" if you want to deselect the orange lines.

Select the inner vertices along the middle line of the cuts you just made.
Shift+clicking will allow you to select or deselect multiple vertices.
Click the blue arrow and pull it upward.
Drag the green arrow to make it more symetrical.
Make a cut along both sides of this new raised ridge. Remember to hold Ctrl along each line to cut it in half.

Next, select the initial middle vertices.
Press Ctrl with the (+) key. This is used to select the next group of vertices around your selection.

Shift click the two end vertices to deselect them. Then press CTRL and + again.
Deselect both end vertices again.

Now we have to shape the slit to be rounded. Drag the blue arrow up. Drag the green arrow a bit to make the lines more straight.

Continue on in this fashion till the outer edge is reached.

When the final edge is adjusted then you may go back and smooth some more.

When finished, you may keep as is or you can click on the "Smooth Vertex" tool on the left toolbar to see if it makes the shape better.

You can also raise the inner ridge again to make it look deeper.

You can go to object mode to get a more shaded view.

End Video Transcript.

Description
Creating a simple vagina.
Disclaimer. These tutorials are for educational purposes. I am not responsible for what is done with the information.

www.mediafire.com/watch/795h2b…

Begin Video Transcript.

Click on a vertice on the crotch and click "View", then "View Selected" to zoom in.

We have to choose where the slit will be.

When decided, click "Knife" on the left tool bar. Just below the 3D view area, there are options for this tool that appear. The option we are most concerned with is Ctrl: midpoint snap. This automatically cuts an edge in the middle.

Choose where the cut will begin. Bring the green square down to the first edge and press "ctrl". You will notice that the green square goes to the middle of that line. Press the left mouse button and the first part of the cut is made.

Go down, and upward like I have. Press the space bar, then the first cut is made.

Make another similar cut in the middle of the cut you just made. Then another similar cut between the outer and inner cut. Then another in the centre. I will show you.

You can zoom in with the mouse scroll wheel if you need a closer view.

Move to a view inside the model. Press "A" if you want to deselect the orange lines.

Select the inner vertices along the middle line of the cuts you just made.
Shift+clicking will allow you to select or deselect multiple vertices.
Click the blue arrow and pull it upward.
Drag the green arrow to make it more symetrical.
Make a cut along both sides of this new raised ridge. Remember to hold Ctrl along each line to cut it in half.

Next, select the initial middle vertices.
Press Ctrl with the (+) key. This is used to select the next group of vertices around your selection.

Shift click the two end vertices to deselect them. Then press CTRL and + again.
Deselect both end vertices again.

Now we have to shape the slit to be rounded. Drag the blue arrow up. Drag the green arrow a bit to make the lines more straight.

Continue on in this fashion till the outer edge is reached.

When the final edge is adjusted then you may go back and smooth some more.

When finished, you may keep as is or you can click on the "Smooth Vertex" tool on the left toolbar to see if it makes the shape better.

You can also raise the inner ridge again to make it look deeper.

You can go to object mode to get a more shaded view.

End Video Transcript.